Heavy Duty 24V Extra Long Stroke (Left & Right) Telescopic Linear Actuator | Swing Gate Automation
Heavy Duty 24V Swing Gate Left or Right Automation with All Metalic gears, powerful and quiet operation. Easy to use manual override using the supplied key in an emergency. The system can handle light and heavy gates up to 175kg maximum weight or 3m maximum length (for each gate).
Emergency Clutch Override
Easy manual override in case of an emergency using the supplied key, slot in and turn clockwise to operate the gates manually.
Actuator Dimensions
Specifications
Motor Voltage
|
24v DC
|
Manual override
|
Via override key supplied
|
Working temperature
|
-10° ~50° |
Maximum stroke
|
650mm
|
|
3m max (for each gate)
|
Gate weight
|
175kg max (for each gate)
|
Absorbed power |
70W |
Current |
5.2A |
Motor speed |
1800RPM |
Thrust |
1800N |
Installation Geometry
Pull to Open Installation
Before beginning installation, identify the left/right side motor. The manual override for the gate motor determines this.
The manual override should not be facing the gate to allow easy accessibility.
Push to Open Installation
Before beginning installation, identify the left/right side motor. This is determined by the manual override for the gate motor.
The manual override should not be facing the gate to allow easy accessibility.
Weatherproof Control Box
The CBSW24 series smart control panel is an easy to connect, simple to setup and feature rich control box vast amount of features as listed below:
Special Features
Party mode: The automatic closing can be cancelled using button 3 on the remote control buttons when expecting a visitor to arrive, reversing a trailer and numerous other uses.
Service Gate Function (12V 250mA max.). Using the second lock output will allow the user to power and control a second electric striker installed on a pedestrian access gate the second lock is powered from the control panel and controlled using button 4 on the remote. APC Wired and wireless Accessories can also be use to control the Lock 2 function.
Accessories Compatibility
Constant 24V DC Accessories Output
Switched 24V DC Output for closing direction (used for safety devices to conserve power, powered on when required)
Open/Stop/Close Inputs for Single Gate Operation and Double Gate Operation
Smart Opening & Closing LED indicators: Green LED on during opening and Red LED on during the closing
Automatic Electric Lock Output
Controlling Options
Any or all of the following may be connected to operate the gate
Remote controls
Entry and Exit push button with isolation key switches (Wired and Wireless Options Available)
Keypads (Wired and Wireless Options Available)
Exit/entry sensors
Intercom system with dry contact output
Automatic switching timer
WiFi Control System (App Based Control)
GSM Control Systems (Mobile Call/SMS based Control)
24V 20 Watt Solar Panel (Upgradable to 20 Watt or 60 Watt options)
Mono Crystalline silicon solar cells with 3mm tempered glass and two sheets of tedlar-polyeaster-tedlar (TPT) and ethylene Vinyl acetate (EVA). This protects against moisture penetrating into the module. The solar panel is supplied with a fence mounting bracket system along with a pre-connected 5 metre cable (maximum cable distance is 20 metres), the solar panel is also fitted with a diode to prevent feed back from the batteries.
Specifications |
Maximuim Power |
20W/40W/60W |
Optimum Operational Voltage |
36V |
Open Circuit Voltage |
43.2V |
20W Panel Dimensions |
640 x 300 x 25mm |
40W Upgrade Panel Dimensions |
535 x 515 x 30mm |
60W Upgrade Panel Dimensions |
805 x 535 x 30mm |
24V 9aH Battery System
Supplied with the automation kit, the 24V Battery System* (2 x 12V 9Ah Batteries) will allow for continued use of the gate system, whether day or night. The system can operate for up to one week of regular residential use without any charge from the solar panel (winter months/wet season) and will automatically recharge from sunlight. When the system batteries are fully charged, it will continue to float charge to keep the batteries topped up and ready for use. In the case of extended use requirements or higher duty, there are upgrade options to 17aH and 33aH battery systems.
*Fully charged batteries will provide 27V and Cuts Off the system at 24V to improve AGM battery life
Remote Features
Specifications
Power Input |
20W 24V Solar Panel (Upgradable) |
Regulator |
Built In On Board Regulator |
Motor Output Voltage |
24v DC |
Battery System |
24V 9aH (Upgradable) |
Working temperature |
-10° - 50° |
RF |
APC Rolling code 433.92mhz |
Lock Output (Primary) |
24V DC |
Lock Output (Secondary) |
12V DC |
Auxiliary Inputs |
0V Momentary Pulse |
Accessories Voltage |
24V DC |
Over current |
1A to 5A |
65mm Rubber Gate Stop
The supplied 65mm rubber gate stop with a steel base is used for the gate alignment and tension whilst they are in the closed position; it also allows the gates to be mounted up to 50mm off the ground.
Being that the minimum vehicle height from the ground is 100mm, it will not interfere with the vehicle. In the case that the vehicle was lower than the typical minimum, the stopper would not cause any damage as it is constructed from solid rubber but retains its general strength from the steel plate used at the bottom side contacting the driveway.
65mm Rubber Gate Stop Dimensions
Wired Double Push Button with Isolation Key
The wired double push button switch is a simple and easy to use method to operate the gate for full gate operation and also pedestrian function.
It is mounted in the general area of the gate and can be isolated by using the supplied keys without affecting the rest of the system, this is handy if you want to continue using the remotes or any other method of operation but wish to stop use of the push button itself.
The push button is wired to the control board using the supplied cable roll. If required the wireless push button can be upgraded to a wireless keypad for higher access security using pin number and can have diffrent pin codes for both the full gate operation and pedestrian function.